Two 2×18-inch subs, same driver, same amplifier board, same 100 Hz target — and yet one build hums, fights a phase hole near 90 Hz and pushes unfiltered low end into the top boxes, while the other drops in and behaves. The part that usually decides which one you get is not the power stage. It is the small board behind the XLR panel: the subwoofer functional module.
The short version first: choose the module by its output routing and input topology, then by the power amplifier it will feed. EQ features and Bluetooth come last, because they are easy to add and painful to change once the cabinet is tooled.
Content
- 1 What a subwoofer functional module is — and what it is not
- 2 Inside the board: five blocks that decide behaviour
- 3 Reading the listing: four modules side by side
- 4 Output mode is the first decision, not the last
- 5 Inputs, level and the hum you will hear
- 6 Matching the module to the amplifier and the driver
- 7 Bluetooth TWS on a subwoofer module
- 8 Checklist before the tooling order
- 9 Frequently asked questions
- 9.1 What is a subwoofer functional module?
- 9.2 Does it include the power amplifier?
- 9.3 What does the high-pass output do for my top boxes?
- 9.4 Can the same module drive 4Ω and 8Ω subwoofers?
- 9.5 Is Bluetooth TWS latency a problem on a sub?
- 9.6 Can crossover frequency, connectors and branding be customised?
What a subwoofer functional module is — and what it is not
In module-based powered speakers, the electronics are split across two boards. The subwoofer power amplifier module delivers current: in the hg-amp.com catalogue, the EON180S-2092 is listed as LP650W into 8Ω with a BTL output, while the EON526-4X2092 is listed as 800W + 800W into 8Ω for double-18-inch boxes. A subwoofer functional module sits in front of that stage and does the signal work: input selection, stereo-to-mono summing, low-pass and high-pass filtering, level and limiting, and routing to the sub amplifier and to the satellite or top-box amplifier.
Keeping those functions on a separate board means one front-end design can drive different power platforms — Class D with LLC resonant supplies for high-power touring boxes, or linear Class AB/H designs where the thermal budget allows. It also means the crossover point, the connector layout and the front-panel behaviour can change without touching the power stage.
Inside the board: five blocks that decide behaviour
Most modules in this class, including the PL28SUB, PL78SUB, S15SUB and S18SUB listed on hg-amp.com, are built from the same five blocks. A small difference in any one of them shows up later as noise, hum, or a crossover that never quite lines up.
- Input stage — combo XLR/TRS, separate balanced terminals, or RCA. It decides what an installer can plug in without an adapter.
- Summing and buffer — combines left and right into a mono feed at a defined gain, so a 2.1 system does not lose level when one channel is quiet.
- Filter block — low-pass for the sub path and, on many models, a high-pass for the satellite feed, fixed or switchable.
- Level and limiter — sets drive into the power stage and keeps a clipped signal away from the driver.
- Output routing — through (full-range) or high-pass to the tops, sometimes with a satellite power trigger.
A change in the filter block ripples through everything else: a higher crossover protects small tops but eats sub headroom, and a lower one pushes excursion onto a driver that may not have the Xmax to spare.
Reading the listing: four modules side by side
Published catalogue text is usually enough to shortlist a module before you ask for a full datasheet. The table below reflects the listings only — where a detail is not published, it is marked as such rather than assumed.
| Module | Documented inputs | Documented output modes | Where it helps |
|---|---|---|---|
| PL28SUB | Line-level input | Full-range output or high-pass output | PA subwoofer front end with a filtered top-box feed |
| PL78SUB | Stereo balanced and unbalanced input | Not stated in the listing | Mixed racks where XLR and RCA sources both appear |
| S15SUB | Two-channel input | Switchable output modes | 2.1 and 1.1 builds sharing a single board |
| S18SUB | Not detailed in the listing | Through output or high-pass output | Wireless source plus a filtered satellite feed |
PL28SUB PA Subwoofer Module with Selectable Through or High-Pass OutputA listed subwoofer module for systems deciding between full-range through and high-pass routing, with adjustable crossover and balanced XLR I/O.View Product →Output mode is the first decision, not the last
Through versus high-pass is the single choice that changes how the rest of the system behaves. A through output passes the full-range signal to the tops and trusts their own filtering; a high-pass output removes everything below the crossover before the signal leaves the board.
On paper the two look similar. In the room they are not. Feeding small 8-inch tops a full-range signal costs them excursion and amplifier headroom that they need for vocals, and it makes the sub/top overlap depend on two independent filters. A high-pass feed from the module keeps the crossover in one place, which is easier to repeat across a production run.
The trade-off is control versus flexibility. If the top boxes already contain a DSP with a matched crossover, a through output keeps the system simple. If the tops are passive or their DSP presets vary between projects, a fixed high-pass from the module gives every unit the same starting point.
Inputs, level and the hum you will hear
Balanced inputs exist for a reason on a sub: the cable run is long, the amplifier gain is high, and a sub reproduces mains hum more obviously than any top box. The PL78SUB is listed with both stereo balanced and unbalanced inputs, which is the practical answer for rental stock that has to accept whatever the previous operator installed.
Two details are worth confirming before production. First, whether the balanced input uses a true differential stage or an impedance-balanced arrangement — the difference shows up in common-mode rejection on long runs. Second, whether the shield is tied to chassis at the input connector only. A second ground path through the RCA socket is the usual source of the 50 Hz hum that appears only when a laptop is connected.
Level matching matters just as much. A module with too much fixed gain forces the installer to run the source low, which raises the noise floor; too little gain and the limiter arrives before the amplifier does.
Matching the module to the amplifier and the driver
The functional module is line-level, so it does not set the power or the load. Those come from the power stage and the driver. What the module must do is present a clean, limited signal that the amplifier can use without clipping, and do it repeatably across a production batch.
For high-power boxes, an LLC resonant supply with a Class D stage is the usual combination because efficiency and weight both matter; the resonant supply behaviour under heavy subwoofer load is worth reading before you lock the BOM. On smaller boxes, a linear Class AB/H stage may cost less and behave more predictably at part load.
Three numbers decide whether the pairing works: the amplifier's rated output into the actual load, the driver's continuous power and Xmax, and the limiter threshold you set on the module. Get those three aligned and the sub will survive a touring season; get them wrong and the first clipped transient will find the voice coil.
S15SUB Two-Channel Subwoofer Module with Link or Crossover OutputA two-channel subwoofer module with balanced XLR/TRS inputs, selectable 90/120 Hz crossover, and link or high-pass output for satellite systems.View Product →Bluetooth TWS on a subwoofer module
The S18SUB is listed with through output or high-pass output plus Bluetooth TWS, which points at a specific product type: a portable or semi-portable sub where the source is a phone or a second speaker rather than a mixer. For that use, wireless is not a gimmick — it removes the last cable in a system that is carried by hand.
Design notes from projects of this kind: keep the antenna area clear of the amplifier's switching node, verify pairing behaviour when the sub and the satellite power up in different orders, and confirm what happens when a wired source is connected while TWS is active. Latency is rarely critical on a sub-only path, but it becomes audible if the same module also feeds full-range tops.
S18SUB Subwoofer Module with Bluetooth TWS and High-Pass OutputA powered-subwoofer front-end module with Bluetooth TWS, switchable bass EQ, and link or high-pass routing for sub/satellite systems.View Product →Checklist before the tooling order
- Confirm the output mode you actually need: through, high-pass, or switchable.
- Fix the connector set and its position on the panel before the chassis drawing is approved.
- Agree on a gain structure with the power stage supplier, not after the first samples.
- Set the limiter against the driver's real power handling and Xmax, not the amplifier rating.
- Define the production test: input sensitivity, filter point, hum level, channel balance.
- Check the ground scheme with a laptop and a mixer connected at the same time.
- Version-control the preset or fixed filter values so batch 2 matches batch 1.
Frequently asked questions
What is a subwoofer functional module?
It is the front-end board of a powered subwoofer. It handles inputs, stereo summing, filtering, level and limiting, then routes the signal to the power amplifier and to the satellite speakers.
Does it include the power amplifier?
No. The module is line-level. It is paired with a separate subwoofer power amplifier module, such as a BTL Class D stage rated for the driver and enclosure.
What does the high-pass output do for my top boxes?
It removes low-frequency content before the signal reaches the tops. That protects small drivers, frees amplifier headroom, and keeps the crossover defined in one place.
Can the same module drive 4Ω and 8Ω subwoofers?
The module itself is load-independent. Impedance and power are decided by the power amplifier stage, so check the BTL rating before pairing a 4Ω driver.
Is Bluetooth TWS latency a problem on a sub?
Usually not, because low-frequency content is less sensitive to a few milliseconds of delay. It matters when the same wireless path also feeds full-range tops or a video source.
Can crossover frequency, connectors and branding be customised?
Yes. The OEM customisation service covers filter values, connector layout and panel details, normally with a sample approved before mass production.
A subwoofer functional module is a small board with an outsized influence on how a powered sub behaves in the field. Decide the output routing and the input topology first, match the limiter to the driver, and the EQ and wireless features become what they should be: refinements rather than rescue work.

English
Español
中文简体









